Snake Shield - Snake Repeller, Solar Powered (679S)

Snake Shield - Solar Powered Snake Repeller features:

• Covers up to 30m in diameter
• Solar powered
• 4 steps to set up
• Best Snake Detterent on the Market with new advance technology

This unit works by emitting a pulsing vibration through the ground and a sound about every 50 seconds to help keep snakes away, a snake is able to pick up these vibrations through its body sensors and fools it into thinking there is danger ahead. A solar panel and a rechargeable accumulator battery collects power by day for operation at night. When the accumulator battery is fully charged, it can supply enough power for around-the-clock operation even on dull days.

How To Deter Snakes.

Step 1) Critical …Before using for the first time: The battery must be fully charged. To do this, simply snap together the two matching black connectors attached to the black & red wires. (One pair coming from the green plastic top and the other pair coming from the battery). DO not join the black wire that runs the vibrator and sound at this time. Leave the Solar Snake Repeller in the sun for two days in bright sunshine or 3 or 4 days if overcast (the head and attached battery can be either on it’s ground probe (stake) or just the head and battery left in the sun.

Step 2) Positioning your Snake Shield(s) …. Choosing the correct location for each unit. The Snake Shield radiates in all directions (full 360 degrees) up to approximately a 15m radius or 30m diameter (about 650 sq m). However we do recommend a 5m overlap (see drawing)

To make the best use of the Snake Shield(s) we strongly recommend installation of 2 or more, about 25 meters apart. Firmer ground, gives a better result. Clay soil will transmit the furthest, while sandy soil will reduce the diameter of the signal. Waterlogged soil should be avoided.

Except for concrete walls/buildings with a foundation deeper than 100mm, the Snake Shields signal will travel through the ground under fences, shallow concrete paths, sheds and behind retaining walls to drive out any snakes that may be hiding around them. These repellers work well in long grass areas. No problem with trees, dog kennels, bushes, chain link fencing.

Step 3) Installing in the ground:

A) Remove the plastic covering on the aluminum ground probe before installing.
B) Make the ground hole with great care, as it is a CRITICAL step. When making the hole for the aluminum stake (probe) keeps the soil firm. DO NOT just dig a hole and fill around the stake as the loose soil will reduce the effective diameter of the signal. The hole must only be driven, use either a crow bar with a point, a round dowel, a metal tube or metal rod about the same diameter (but no larger) than the probe. NEVER use a hammer to drive in the aluminum probe (stake), and NEVER, force the tube into the ground by pushing down on the plastic top/solar panel. The head should only be added once the tube is firmly in place. As a final positioning before the head is installed you may carefully push the probe with a block of softwood (like Pine) placed over the tube, but remember probe (stake) must not be deformed or damaged, otherwise the plastic head will not fit on correctly.
C) Leave about 50mm of aluminum stake above the ground, more if the area is prone to flooding. The unit is weatherproof, but is not waterproof: Rain presents no problem, however the top of the aluminum tube must never be underwater. If there is the potential for hail the unit should be either covered or removed. In winter (if you are not concerned about snakes) we strongly recommend the units be stored undercover.

Step 4:

Installing the head: Now that the battery is fully charged, and the ground probe is in place it’s time to join the red connectors on the white wires starting the vibrator and sound. If you have more than one unit it is recommended to stagger the starting times. In other words when starting a second unit wait for the beep from the closest unit and then join the wires about 25 to 30 seconds later.

To start the MP Plus simply press the On/Off rubber covered button on the underside of the head. When starting for the first time you will know the unit is performing correctly if you hear the unit go through it’s 3 stage multi pulse cycle. First a single beep, followed by a triple beep, followed by 5 beeps.

With the activation test over, within about 60 seconds you will hear a single beep starting the first 2 day rotation of the 3 different pulses.

Warranty: This product is warranted against faulty material and or workmanship for the period of 3 months. Our obligation under this warranty is limited to repair or replace the unit (at our discretion. Prior to return, you must email telling us what you would like us to do, and why. Return without authorization will not be accepted

The  warranty shall not apply and is not limited to, any parts or materials which have been subject to accident, negligence, alteration, abuse or misuse whether intentional or by accident. We shall not assume any responsibility for any consequential damages of any kind whatsoever.

Furthermore, the warranty is invalid if proof of purchase can not be produced. The return postage costs are at the buyer's expense.

The Snake Shield is a snake repeller or a snake deterrent, as mentioned in the manufacturer's instructions, this unit is not 100% foolproof, but will greatly reduce any unfortunate encounters with snakes. To this end, Dogmaster Trainers points out that this unit is designed to discourage snakes into the area where the Snake Shields are located. However, no responsibility or liability can be accepted, should a snake enter the area and an unfortunate encounter occur.